1、使用环境：

铺设防静电地板的房间环境控制要求温度：15℃~35℃,相对温度：45%RH~75%RH。

2、装饰面地板：

1.禁用尖锐、锋刃的器具在活动地板的装饰面上直接施工操作，防止破坏装饰面的防护电性能和美观程度。

2.使用过程中禁止人员从高处直接跳落到防静电地板上，及在移动物品时野蛮搬运，砸伤地板。

3. 在活动地板上搬运物品时，禁止直接在板面上推动物体，使物体与地面之间直接摩擦，造成板面划伤。

4.在搬运物品时，应用带有胶轮的推车进行搬运或在物体的轮廓与地板之间铺设隔离垫，防止板面损伤。

5.在防静电地板活动版面上放置较重物品时，应平稳摆设，以免砸伤地板。

6.对地板下部空间的设备进行维护时，应用地板吸板器进行地板安装，拆装地板要轻拿软放，以免损伤防静电地板。

7.使用中可用干净的拖布和抹布保持板面的清洁，注意不要把大量的水、清洁剂等液体洒在地板上，以免影响防防静电地板使用寿命及影响防静电地板下面的线路及设备的正常运行。

3、裸地板和通风地板

1.使用中应防止活动地板的防静电喷塑层划伤，如发现划伤应用灰色的漆进行补刷，保证涂层完整。

2.防止体积小的物体掉入通风地板的通风口(如硬币、钥匙、曲别针、大头针等)以免损坏通风调节器等设备。

1, using the environment:





Laying anti-static floor room temperature environment control requirement: 15 ℃ ~ 35 ℃, relative humidity: 45% RH to 75% RH.





2, decorative flooring:





1. The disabled, the blade sharp instruments directly on the floor of the decorative construction operation, to prevent damage to decorate the protective performance and beautiful degree.





2. In the process of using prohibited personnel directly jump from a high place fell to anti-static floor, and rough handling during shifting of the objects, above the floor.





3. On the floor when transporting goods, direct drive objects on the plate, directly to the friction between the object and the ground, causing surface scratch.





4. When handling items, applied with the rubber-tired cart to carry or between the object and the outline of the floor laid isolation pad, to prevent surface damage.





5. On the anti-static flooring activity layout, placing heavy objects should be smooth and decoration, so as to avoid hitting the floor.





6. The lower part of the floor space of the equipment maintenance, the application of floor suction plate on the floor installation and disassembling floor should take put down soft, so as not to damage the anti-static floor.





7. Use of the available clean mop and cloth to keep the surface clean, be careful not to spill a lot of water, detergent liquid on the floor, lest affect and anti-static floor service life, and anti-static floor below the normal operation of the line and equipment.





3, bare board and ventilation and floor





Should prevent floor 1. The use of antistatic coating layer scratch, such as found scratch the grey paint brush up, ensure complete coating.





2. To prevent the small size of the object fall into the ventilation of the floor vents (such as COINS, keys, paper clips, pins, etc.) in order to avoid damage to the ventilation regulator, etc.